.
.
.
.
.
.
Cetak

Fatal Accident Case

DateTitle CaseSummary CaseClassification CaseContributing FactorsObservation
31-10-2014Died due to burns
Location: Kilang Sawit, Johor
The victim who was assigned to perform work of replacing the bricks inside the boiler furnace. The accident occurred when the furnace collapsed and the hot ashes spread out and caught fatalBurns
  1. No safe work procedure
  2. Lack of supervision from employer
  3. Failure of conducting risk assessment on the repair
24-10-2014Died being crushed by pallet
Location: Kilang, Johor
The incident took place during the removal of the final product namely tubing wrapping plastic from stor into the container using forklift while being watched by the victim. At that time, it was said that wrapping plastic tubing which is on the pallet has slipped and fell on the victimfatalInternal injuriesNo safe work procedure
17-10-2014Died caught in a backhoe
Location: Kuari, Perlis
Victim, a stone crusher backhoe?s driver was assigned to do work of breaking the stone on the hill. The accident occurred as the victim reversing his vehicle after the completion of his work. Victim who fell approximately 20 meters along with the backhoe was found trapped in the driver's seatfatalSerious bodily injury
  1. No safe work procedure
  2. No supervision from the employer
16-10-2014Died falling from height
Location: Tapak bina, Johor
The victim was found lying on the floor as it was believed he fell down from the place where he carrying works of removing form workfatalInternal injuries
  1. Fail to wear safety harness
  2. No supervision from the employer
08-10-2014Died falling from height
Location: Kilang Sawit, Johor
Victim was assigned to repair the Gear Box at Incline Conveyor. He fell down as he stepped on rotten working platformfatalSerious injuries all over bodyFailure to conduct access to workplace (working platform) risk assesment
07-10-2014Died being struck by lorry
Location: Perladangan, Kedah
Victim, a lorry driver was killed after being run over by his vehicle. Prior to the incident, he parked the lorry on the steep road with intention to unchained the lorryfatalSerious injuries to the body
02-10-2014Died crushed by tree
Location: Kawasan pembalakan, Sarawak
Victim and his colleague was assigned to cutting down trees. Victim cut a tree and as a result tree topple on another tree and caused that tree toppled over victim?s headfatalSerious injuries to the head
29-09-2014Died being crushed by mobile crane?s boom
Location: Tapak bina, Pahang
A mobile crane was carrying works of lifting a bundle of scaffolding as victim was working within the working radius. Due to excessive load, the crane overturned and toppled over victim fatalSerious injuries to the body
  1. Failure to comply with safe work procedure
  2. Failure of the crane?s operator to read load chart
  3. Excessive load lifting (over load)
  4. Failure of the employer to ensure that the area is safe when lifting work carried out
23-09-2014Died crushed by tree
Location: Kawasan pembalakan, Sarawak
Victim and his colleague was assigned to cutting down trees. Victim cut a tree and as a result tree topple on another tree and caused that tree toppled over victim?s headfatalSerious injuries to the head
20-09-2014Died from falling into ravine
Location: Kawasan pembalakan, Sarawak
Victim, a lorry driver was found dead. He is believed died due to falling into the ravine with his lorryfatalSerious injuries all over body
15-09-2014Died being hit by mobile crane
Location: Tapak bina, Selangor
Victim, crane operator was lifting a pile of 'reinforced bar' to be locate at one place between two building blocks. As the lifting works is in progress, suddenly crane off balanced and overturned. Victim was crush by the crane as he tried to got out of the cabin fatalSerious head injuriesFail to comply with mobile crane standard procedure for lifting works
13-09-2014Died due to the exposure of hazardous chemical
Location: Tapak bina, Johor
Victim was found unconscious after got out of the cabin. During the incident, he was carrying out the air-conditioner maintenance works fatalDied of Acute Pulmonary DiseaseThere is a chemical spill in cabin
13-09-2014Died being struck by bricks
Location: Tapak bina, Pulau Pinang
The victim has been struck by falling bricks from the lifting tray. At the time, a tower craned was used to lift the lifting tray at the height of 26 metersfatalSerious head injuries
13-09-2014Died being struck by pallet
Location: Tapak bina, Johor
The victim and his colleagues were removing the glass door from the truck into the factory , which is still under construction . As the work undergoing, suddenly pallet containing glass door fell from the truck and hit the victimfatalSerious head injuries
11-09-2014Died being caught in a machine
Location: Kilang, Selangor
The incident occured as the victim was tagging the name on the product by using the designed machine. He died due to got caught between two arms of the machinefatalSerious injuries to the bodyFail to comply the safe work procedure in operating the machine
09-09-2014Died being crushed by forklift
Location: Tapak bina, Pulau Pinang
The unbalanced forklift driven by the victim has caused it to overturned and crush the victimfatalSevere bleeding in the head
08-09-2014Died falling from 10 metre height
Location: Tapak bina, Pulau Pinang
Victim was standing on plywood plate while carrying out plastering works. Suddenly, the place where he was standing has broken causing him to fall downfatalSevere bleeding in the head
02-09-2014Died falling from height
Location: Tapak bina, Kuala Lumpur
Victim was assigned to carry out binding and plastering works. He is believed has slipped and fell on the First Lower Ground while doing his jobfatalSerious injury all over body
  1. Fail to comply with the safe work procedure
  2. wearing personal protective equipment (PPE)
19-08-2014Died being hit by object and fell
Location: Kilang, Pulau Pinang
Victim fell down due to being hit by broken 'lifting lug' on the shaft. The incident took place during the preparation of lifting works using Overhead Travelling Crane (OTC)fatalSevere head injury
18-08-2014Died being crushed by wood pallet
Location: Kilang, Sarawak
Victim, 8 years old children died being struck by wood pallet as he attempted to climb the wood palletfatalDispersed workplace
18-08-2014Died being crushed by concrete structure
Location: Tapak bina, Selangor
Three victims were crushed by falling concrete structure as they fell down along with the structure. Prior to the incident, they were performing installation works of that concrete structurefatalSerious injuries all over body
  1. Fail to comply with the safe work procedure
  2. lack of supervision from the employer's side
15-08-2014Died due to electrocution
Location: Perladangan, Sabah
He died being struck by eletricity as he was cutting the oil palm fruitfatalBurns on the right and left wrist and other part of the body
  1. Aluminium pole struck the electrical line
  2. Fail to carried out risk assessment
13-08-2014Died being struck by vehicle
Location: Tapak bina, Pulau Pinang
Victim, a flagman was struck by vehicle while carrying his duty on the highwayfatalSerious injury to the bodyThe vehicle was drive by drunken driver
09-08-2014Died falling from height
Location: Kilang, Selangor
There is an explosion at the top of short fiber storage tank as a result of the welding process. The explosion caused the workers thrown and fell from a height of 8.5 meters fatalSerious head injury
  1. The existence of flammable gaseous
  2. Failure to comply with the SOP of obtaining a work permit for confined space
09-08-2014Died falling from height
Location: Tapak bina, Sabah
The accident happened on the 16th floor as the victim is believed was slipped and fell into elevator pitfatalSerious injuries all over body
  1. Life line to hook safety harness were not installed
  2. The slovenly condition at the workplace
02-08-2014Died due to electrocution
Location: Kebun Persendirian, Johor
Victim is believed carrying works of knitting the oil palm fruits using his aluminium poles. He?s been electrocuted when his poles got stuck in the transformerfatalElectric shock
26-07-2014Died being crushed by Mechanical Buffalo @ badang
Location: Ladang, Johor
Victim was driving mechanical buffalo loaded with oil palm fruit along the steep road about 15 degree slope. That vehicle suddenly overturned and crash the driver fatal
23-07-2014Died falling from height
Location: Tapak bina, Kedah
Victim fell from level 2 after being hit by hook and block due to broken fly jib of mobile cranefatalSerious injuries in the mouth, nose, hands and head
  1. Mobile cranes poorly maintained
  2. No safe work procedure for lifting works
23-07-2014Died being hit by Concrete Bold
Location: Tapak bina, Kuala Lumpur
The victim was crushed by concrete wall as he was carrying wall hacking worksfatalSerious head injuries1)Fail to conduct risk assessment for hacking works 2)The employer has failed to fully exercise supervision over the workers
21-07-2014Died stung by wasps
Location: Perladangan, Johor
A worker has been stung by wasps while fatalStung by wasps
21-07-2014Died being caught in a Goods Lift
Location: Pasar Mini, Perak
Victim's head was caught between Frame Cage and Landing DoorfatalSerious injuries to the headDesign of the lift does not meet the minimum safety standard
18-07-2014Died being hit by Machine Tractor Hammer structure
Location: Tapak bina, Perak
The victim was struck by the structure as he was dismantling the top structure of the modified Hammer Machine Tractor fatalSerious injuries to the head
  1. No safe work procedure for dismantling the machinery
  2. Lack of supervision
14-07-2014Died falling from height
Location: Loji Jana Kuasa, Johor
Victim is believed to have fallen while trying to access to higher level by climbing the scaffoldingfatalBroken left arm and fractured ribsNo safe work procedure
13-07-2014Died being pinned by tractor
Location: Perladangan, Johor
The incident took place as victim hit the divider with his tractor. The collision caused the tractor overturned and crash the driverfatalSevere head injury
11-07-2014Died from being run over by a lorry
Location: Ladang, Sarawak
Victim, a lorry driver died being run over by a lorry. The incident occured when he was driving downhill in the lorry when suddenly the brakes malfunctioned. He jumped out of the lorry but was instead run over by the lorryfatalSevere chest injury
10-07-2014Died being run over by trailer
Location: Ladang, Johor
Victim was standing on the drawbar trailer towed by a tractor. He is believed to have fallen and being run over by trailerfatalWaist injuryUnsafe act
07-07-2014Died crushed by backhoe
Location: Tapak bina, Kedah
Backhoe was overturned and fell on the victim as it was lifting the drain blockfatalSerious head injuriesNo safe work procedures
04-07-2014Died from falling into the tank
Location: Tapak bina, Sarawak
2 workers has fallen into the opening tank that filled with water. They were doing works of gantry pipe installation and welding fatalDrowningFloor opening
03-07-2014Died due to drowning
Location: Hotel, Sabah
A child who was not being accompanied by his guardian found dead at the bottom of the poolfatalDrowning
  1. Negligence
  2. The absence of life guard at the scene
03-07-2014Died being pinned by steamroller
Location: Tapak bina, Perak
Victim was carrying road leveling work using steamroller. Suddenly he lost control of the steamroller caused the vehicle fell into the canal and crashed himfatalSevere injuries to the bodiesNo safe work procedure
03-07-2014Died being crushed by truck
Location: Ladang, Sabah
Truck was driving uphill during the incident as it suddenly lost control and overturned. Truck crash the victim as she was flung from the truck. During the incident, she was seated at the back of the truck fatalSevere injuries to the bodies
  1. Truck was not properly well maintain
  2. Truck used was not suitable for transporting workers
27-06-2014Three died due to concrete wall collapsed
Location: Tapak bina, Johor
Three workers died after being struck by concrete wall collapsed as they were carrying works of trench excavationFatalNo safe work procedure
26-06-2014Died being pinned by forklift
Location: Kilang beras, Perak
Forklift overturned and crash the driver while carrying work of lifting and placing jumbo bagFatalBroken hip bone-No safe work procedure -Victim has never undergone intensive training regarding to forklift handling
26-06-2014Died being buried
Location: Tapak bina, Johor
The trench wall collapsed and buried the victim. Prior to the incident, he was doing works of trench excavationFatalNo safe work procedure
24-06-2014Died falling from height
Location: Tapak bina, Pulau Pinang
Victim was assigned to sweep garbage at every floor. He is believed to have fallen from a high place and was found lying on the balcony at level 4FatalSevere head injuryNo safe work procedure
22-06-2014Died struck by backhoe
Location: Ladang, Pahang
Victim, a mechanic was carrying maintenance works on backhoe. The backhoe was lifted using a ' jack '. Backhoe has fallen and struck the victim due to instability position of the bakhoe FatalBackhoe was not in stable position
14-06-2014Died due to drowning
Location: Ladang Ternakan Itik, Perak
Victim, a tractor driver was carrying land leveling works before he and his tractor fell into the lakeFatalDrowningFail to conduct risk assessment
09-06-2014Died struck by tree
Location: Pembalakan, Sabah
Victim was struck by tree during forest clearing work FatalSerious injuries all over bodyKnowledge employers about OSH are at a minimum level
06-06-2014Died due to fall from roof
Location: Tapak bina, Kedah
Prior to the incident, victim was installing roof trusses with his colleague. He is believed had fallen from the roof at a height of approximately 18 feet from the ground Fatal-No safe work procedure -No supervision by the employer
02-06-2014Died falling from height
Location: Tapak bina, Johor
Victim was carrying out work of upgrading grill on a balcony at level 4. He is believed to have fallen along with the iron gril that he was welding.Fatal-Unsafe act for not wearing safety harness when working at height -No safe work procedure
28-05-2014Died by insecticide poisoning
Location: Ladang, Perak
Victim was diagnosed with organophosphorus as he finished doing the activities involving handling of the insecticideOccupational poisoningExposed to hazardous chemicalsLack of supervision of workers to ensure them clean up after handling any hazardous chemicals
28-05-2014Died due to drowning
Location: Dermaga, Perak
The vehicle skidded and fell into the sea while trying to make a 'U' turnFatalDrowningIncompetent driver
26-05-2014Death by electric shock
Location: Pusat membeli belah, Kuala Lumpur
The victim was electrocuted as he was doing maintenance workFatalElectrocutionUnsafe working condition
25-05-2014Died being hit by shovel
Location: Kilang, Johor
The victim was hit by shovel as it move backwardsFatal1)The driver has no training records on driving the shovel 2)Shovel is not equipped with reverse alarm sound
22-05-2014Died crushed by forklift
Location: Kilang, Kuala Lumpur
Forklift overturned and fell on top of the victim.FatalSerious injuries to the headVictim is not qualified to operate the forklift
19-05-2014Died faling from height
Location: Perumahan awam, Kuala Lumpur
8 years old boy was found dead on the floor. He is believed died due to falling from 15th floorFatalSerious head injuriesVictim has entered the scene without permission and there are elements of negligence on the part of contractor and authorities to ensure barrier on the roof is closed as it has been opened for site visit
19-05-2014Died falling from 6th floor
Location: Tapak bina, Johor
Victim was patching potholes on the wall. During the incident, he was standing on the scaffolds with walls openingFatalSevere injuries to the bodies-Not wearing safety harness when working at height -Railing is not installed on the scaffold to prevent fall
16-05-2014Death by electric shock
Location: Tapak bina, Kuala Lumpur
The victim was electrocuted as he was testing the circuitFatalElectrocution
05-05-2014Died falling from height
Location: Tapak bina, Johor
A pile of iron rod tube that has being lifted by a crane has hit the victim causing him to fell approximately 9 metersFatalSuffered severe head injuries and internal bleeding-No safe work procedure for lifting work
-incompetent signalman
05-05-2014Died struck by lightning
Location: Tapak bina, Kuala Lumpur
The victim was killed by lightning as he was pouring the concreteFatalThe victim was working in the open and no lightning detector at the scene
04-05-2014Died was buried under by concrete collapse
Location: Tapak bina, Johor
Victim was concreting the floor as support structure for formwork fell onto himFatalSerious injuries to the bodyFails to provide PE Design for a floor support structure
22-04-2014Died falling from height
Location: Tapak Bina, Johor
A general worker fell down from 26th floor as he was performing floor tiles installationFatalSerious injury to the bodyLack of supervisory
21-04-2014Died being struck by rubber wood from the truck
Location: Kilang, Perak
A lorry driver died being hit by rubber wood as he trying to untie the knotFatalSevere head injuryThe composition of the wood was above the height of the bar (retaining) on lorry
17-04-2014Died caught between two brick trucks
Location:
The victim went into two moving brick trucks and was caught between them Issue 1 NOISerious injury to the hip
17-04-2014Died being hit by lorry
Location: Ladang, Johor
The victim was driving up the steep road using the truck. The truck hit the divider and overturned. His head was struck by truck.FatalSerious injury to the head
13-04-2014Died struck by circular concrete
Location: Gudang, Perak
Victim, aged 10, was playing in the concrete tube while the concrete was being rolled by his/her friend. The concrete tube was said to have slipped and fell, crushing the victim's head FatalSerious head injuryWarehouse does not have a fence / barrier to prevent the public from entering the premises
11-04-2014Died due to drowning
Location: Tapak bina, Perak
Victims carry out land clearing work using bulldozer. He is believed drowned after falling into the mine along with bulldozer. FatalDrownedRain over the last few days may weaken the structure of the ground.
08-04-2014Died being crushed by concrete gate
Location: Tapak bina, Pahang
Victim was struck by falling concrete gate due being hit by a lorrySerious bodily injury
02-04-2014Died falling from height
Location: Tapak bina, Pulau Pinang
The victim fell from a height of 15 meters as he was nailing woodFatalSevere head injury1) Unsafe working condition
2) Negligence of safety measure
17-03-2014Fatal accident involving Express Bus
Location: Lebuhraya, Perak
An accident involving express bus has occured at 301.5 KM north-south expressway. The driver was killed while 2 passengers were injured.FatalRoad slippery due to rainy day
The slopes and winding road
10-03-2014Died falling into depth
Location: Perladangan - Johor
The driver fell into the ravine as he was reversing the tractor. The driver was found pinned between the steering and tractor body.FatalInjury to the chestNo warning signs at intersections
No records of training given to the driver
03-03-2014Died falling from height
Location: Kilang - Johor
The victim had fallen down as the floor he stepped on broke.FatalSerious injury to the headWorn and fragile floor
24-02-2014Died falling from height
Location: Tapak bina, Kuala Lumpur
The victim fell down the void area while performing the installation of the working platform on scaffoldingFatalNo safe work procedure
12-02-2014Death pinned by tractor
Location: Perladangan, Johor
Victimís body had been run over by a tire as he slipped down the tractor he was driving.FatalInjuries to the chest.
11-02-2014Died caught in an tractor
Location: Perladangan, Johor
The victim was died being crushed by tractor on his way down to collect palm fruits.FatalSerious injury to the neckSteep road conditions
08-02-2014Died falling from height
Location: Tapak bina, Johor
Victim fell to the ground as he was dismantling the scaffoldingFatalNone specified Fail to perform risk analysis on the scaffold dismantling procedure
19-01-2014Fatal accident involving Express Bus
Location: Lebuhraya, Johor
An accident involving express bus has occurred at 107.2KM North-South Expressway. 3 passengers were killed in this accident. Fatal-The company failed to provide safe driving procedures.
17-01-2014Falling into the oil reservoir
Location:
Victim slipped and fell into the reservoir containing hot water and oil. Fatalsecond degree burnsAccess to the workplace is unsafe and not properly maintained
05-01-2014Died falling from height
Location: Tapak bina, Johor
As the victim installing the wall cladding to the building structure, he fell from a height of 12-18 metres. FatalSerious injury to the headInappropriate usage of PPE.
31-12-2013Died falling from height
Location: Tapak bina - Johor
Victim fell from a high place while performing his duty of installing the roof of a hall.FatalSerious head injuryFailure to wear Personal Protective Equipment (PPE)

Unsafe workplace
17-12-2013Died pinned by containers
Location: Pelabuhan - Pulau Pinang
Accident involving a local worker who was caught between two containers while inspecting the seal number of a container.FatalSerious head injuryFailure to practice safe work procedures
13-12-2013Died due to drowning
Location: Kilang - Pahang
Victim fell into a pond as he was collecting water samples for laboratory work.FatalDrowningNo safe work procedure

Inadequate supervision as the task of collecting samples was new to the victim and he started doing this for only a few days.
12-12-2013Died crushed by collapsing wall
Location: Tapak bina - Johor
Incident occured during housekeeping works when suddenly a wall collapsed and crash onto the victim.FatalWhole body injuryBrickwork of the wall was not properly done
05-12-2013Died caught between objects
Location: Ladang - Johor
Victim was found pinned between a truck's body and head. At the time, he was doing repair works on the truck.FatalBroken hips / legsUnsafe act

Truck was not maintaned on a regular basis Truck was not maintaned on a regular
02-12-2013Death due to electrocution
Location: Tapak bina - Sarawak
Victim was electrocuted while doing service line installation from a house to a utility pole.FatalElectrocutionFailed to do hazard identification, risk assessment and risk control over the work to be done.
23-11-2013Died being hit by tractor
Location: Ladang - Johor
During incident, the victim who was driving a tractor came down a steep and sharp corner. He lost control of the tractor and as a result, the tractor overturned and crash onto him.FatalStruck by tractorPoor road conditions which does not meet specifications
18-11-2013Died struck by aluminium formwork
Location: Tapak bina - Kuala Lumpur
A 7 kg aluminium plate struck onto the victim's head. He was pronounced dead at the hospital.FatalSerious injury to the head
12-11-2013Died falling from height
Location: Tapak bina - Kuala Lumpur
Victim is believed to have lost balance while boarding a hanging platform. A sudden slight movement to the platform caused the victim to slip and fell down.FatalSerious injuries all over bodyNo safe work procedures
07-11-2013Died being crushed by mirrors
Location: Kedai cermin - Johor
Accident occured in which the victim was crushed by 100 pieces of mirrors weighing 2 tonnes while unloading them.FatalSerious injuries all over body
07-11-2013Died falling from height
Location: Ladang - Johor
The victim, who was standing on a wagon pulled by a tractor, fell down to the ground. At that time, the tractor made turn and the victim lost balance causing the fall.FatalBroken neckFailure to perform risk assessment on the wagon used
30-10-2013Killed by moving truck
Location: Tapak Bina - Johor
Initial investigations revealed that the victim was likely hit by a truck without being noticed by the truck driver. Rain in the morning and afternoon caused slippery and muddy soil conditions that may result in the victim slipping and fell towards the moving truck.FatalSerious injury all over body
28-10-2013Died caught between roller conveyer
Location: Kilang - Sarawak.
Victim was instructed by supervisor to change the position of an uneven conveyor belt with an adjustable spanner at the conveyor roller adjuster. The batching plant is in operation when this activity was undertaken. The victim tried to clean out stones under the conveyor roller using an air hose. Suddenly the victim's head hit the top of the conveyor belt while the air hose was caught by the roller causing the victim to be pulled by the air hose and eventually he was pinched.FatalSerious injuries to head and left armEmployer failed to provide a safe working system for work involving adjusting the conveyor floor for batching plant.
22-10-2013Died due to electric shock
Location: Tapak Bina - Johor
Victim was allegedly electrocuted while cleaning the pipeline of new installed air conditioner.FatalElectrocutionWork premises seems watery and through observation it was found that severe electrical wiring was not properly maintained and fully inspected by a competent person.
13-10-2013Died due to severe burns
Location: Kilang - Johor
Accident happened due to the problem of a "top valve" pad of column 3 in L2 section where the valve could not be closed. The victim went alone to L2 area. Afterwards the victim suddenly ran back to the control room and fell down before reaching the control room. The victim is believed to had opened the wrong valve.FatalSevere burnsAccident happened due to the victim opening the wrong valve.
10-10-2013Died hit by lorry
Location: Kawasan pembinaan jalan raya - Johor
A contractor died after being hit by a lorryFatalInjury to limbs and headAccident occured due to a lorry entering the emergency lane and hitting the worker while the worker was placing trafic cones on the road.
06-10-2013Died falling from scaffolds
Location: Kilang - Kedah
Victims was a sub-contractor employees was doing welding work on a warehouse door. The door fell onto the scaffold and caused victim who was on the scaffold to fall down about 10 feet to the ground.FatalSerious injury to the headNo safe work procedure for working at height
08-09-2013Died due to fire
Location: Tapak bina - Kuala Lumpur
A fire incident took place inside a building under construction. The victim who working inside the area was found dead.FatalSuffocation from smoke
27-07-2013Death due to structural collapse
Location: Kedai Cuci Kereta - Johor
Concrete wall of a building next to the car wash collapsed and struck the victim.FatalDied struck by falling object
17-07-2013Died due to caught in the lift
Location: Flat perumahan awam - Kuala Lumpur
Incident occured when the lift suddenly stopped between floor 2 and floor 3. Victim climbed out of the lift when suddenly the lift started moving downwards and caused the victim's head to be caught between the "header car door" and "door hanger landing". He died at the scene.FatalThe victim's head was caught between objectsLift was not functioning normally
17-07-2013Died being hit by object
Location: Tapak Bina - Johor.
The victim is believed to be lifting a pipe using a tractor at the time of the incident. He was trying to loose the chain once the pipe was laid on the ground, then suddenly the bucket at the back of the tractor alighted and hit the victim's head.FatalSerious injuries to the head
22-06-2013Worker electrocuted to death
Location: Pusat Konvensyen
The victim may have suffered electrocution while cutting a cable running with electrical current causing the victims left hand to be stuck to the cable.FatalElectrocution
20-06-2013Died after right hand was cut off in Conveyor Belt
Location: Kilang - Johor
The incident occured when the victim was cleaning wood chips at a conveyor belt. The victim was too close to the conveyor, resulting the shirt worn being pulled in by the conveyor belt. This caused the victim's right hand to be cut off.FatalDeath due to loss of bloodThe employer failed to ensure safe and working procedures, especially at the Refinery Chipper Log Yard section.
11-06-2013Killed being thrown from tractor seat
Location: Ladang - Johor
The victim was thrown away from a tractor's seat while driving down a steep path.FatalIncompetent driver
10-06-2013Died caught between objects
Location: Kilang - Kedah
Victim who is a foreign worker was pinned between a gantry crane motor and a pile of iron. The crane operator didn't realize the victim was there at the time of incident.FatalCaught between moving and stationary objectsNo safe work procedure
09-06-2013Died falling for height
Location: Tapak bina - Johor
The victim is believed to have died after falling from a height of about 10.80 meters from the floor level. At the time, the victim was undertaking cleaning works at a reserve water tank.FatalSevere body injuries due to falling from height.No supervision for working at height
05-06-2013Collapse of Reinforced Concrete Coping
Location: Tapak bina - Johor
A building structure collapsed while two workers were opening the mold of RC Coping while their position was exactly above the structure. As a result, the two workers fall down to the ground. One of them suffered minor injuries while another was killed after the structure collapsed on him.FatalStruck by falling objectsFailure of structure
27-05-2013Died caught in a crane cabin
Location: Tapak bina - Kuala Lumpur.
The incident took place when the victim who worked as a crane operator was trying to lift a 7 tonne Vibrohammer using a crawler crane. Suddenly the crane overturned and trapped the operator inside the crane cabin.FatalCaught in the crane cabinLifting excessive load
08-04-2013Died in car accident
Location: Ladang - Johor
The victim was on his way to conduct pesticide spraying when he was hit by a four wheel drive.FatalStruck by moving objects
04-04-2013Died due to electrocution
Location: Kawasan perumahan - Johor
Victim was found dead due to electrocution. Victim is believed to be in the middle of checking the condition of lights which were malfunctioned.FatalElectrocutionThe employer failed to ensure electrical leakage currents that caused shock to the employee as well as the failure of the employee to ensure the exact cause of the lights' failure.
02-04-2013Sky Lift overturned while doing roof repairing works
Location: Flat Perumahan Awam - Kuala Lumpur
Victim caught in the cage after the sky lift overturned.FatalCaught in between object
25-03-2013Died after inhaling toxic gas
Location: Loji - Negeri Sembilan
2 victims died after inhaling toxic gas while transfering schedule wastes into the storage.FatalInhalation of toxic gasInappropriate usage of PPE
25-03-2013Died due to suffocation
Location: Kilang - Pulau Pinang
An explosion and fire broke out at a factory. During the time, the victim was working inside and he failed to escape. He is believed died due to suffocation.FatalSuffocation
20-03-2013Died hit by car
Location: Bahu jalan - Johor
Two workers died after being hit by a vehicle. Atthe time they were on the road shoulder fixing their lawnmowerFatalSerious bodily injuryNo safe work procedure for the activities near roads
14-03-2013Died being buried
Location: Tapak bina - Johor
Victim died due to suffocation when he accidentally fell into a ditch which the victim himself digged and the surrounding earth afterwards fell into the ditch burying the victim.FatalSuffocationUnsafe working area
14-03-2013Died falling from height
Location: Tapak bina - Pulau Pinang
Victim fell off from the 24th floor while performing the installation of a curtain wall.FatalInjury to the head and bodyNo safe work procedure
14-03-2013Died struck by moving object
Location: Landasan kereta api - Kuala Lumpur
Victim was carrying out visual inspection on arailway when train suddenly came and hit him. He died at the scene.FatalInjury to the bodyNoncompliance with the existing Safe Operating Procedure
17-12-2012Died falling from height
Location: Tapak Bina - Pahang
Victim fell from a height of 15 meters while coming down a roof. At the time of incident, victim was replacing the roof of a building.FatalSerious injury to the head and bodyNo safe work procedure
06-12-2012Killed being crushed by mechanical buffalo
Location: Ladang - Johor
Victim died at the scene due to being crushed by an overturned mechanical buffalo after it hit a rock.FatalSerious injury to the chestLack of skill in driving machinery
03-10-2012Killed in an electrocution accident
Location: Kilang - Johor
Victim is believed to have died of electrocution while performing cutting of steel structure works.FatalInjury to the arm and waistNo safe work procedure and supervision
02-10-2012Died falling from heights
Location: Tapak bina - Johor
Victim fell off the 4th floor of a building where he was working. He complained of headache before the incident. He is reported to have died in hospital.FatalSerious injuries to bodyNo safe work procedure
29-07-2012Died falling from heights
Location: Tapak bina - Kedah
At the time of incident, victim was working on a scaffold when he fell from height of 12 feet. He was taken to the hospital for treatment and pronounced dead afterwards.FatalSerious bodily injuryNo safe work procedure
23-07-2012Died falling from height
Location: Tapak bina - Kuala Lumpur
During the incident, the victim was carrying out works on a 'working platform' to install the 'lift core wall' in a lift pit. Suddenly the working platform collapsed causing the victim to fall down. The seriously injured victim was brought to the hospital for treatment and was confirmed to have died the following day.FatalSerious injuries to waist and legs
19-07-2012Died after crushed by lorry
Location: Ladang - Pahang
The incident which happenes at 8.30 am involved a foreign worker who died after being crushed by a lorry filled with fertizilers.FatalSerious injuries to the bodyNo supervision of workers
03-07-2012Died being pinned
Location: Tapak bina - Pahang
The incident involved a foreign worker who died being pinned in cabin after a crawler crane fell over while lifting a load.FatalSerious injuries to the headNo safe working procedure for lifting works were provided as well as the weight of the lifted load exceeded the permitted limit.
28-06-2012Died crushed by tractor
Location: Ladang - Perlis
Victim who is foreigner died after falling from and hit by a tractor. Victim was standing on the connection between the tractor and water tank.FatalSerious injuries to the headNo safe work procedure.
20-06-2012Died falling from heights
Location: Kilang - Johor
The victim fell from a height of 5 metres while repairing floodlights in the workplace. The victim was taken to the hospital and was confirmed dead a day later.FatalSerious injuries to the headWork was performed without supervison. A life line that should be attached to the safety harness was not prepared.
16-06-2012Died falling into water
Location: Petroleum terminal - Johor
The victim, a Malaysian citizen, fell into water and died. During the incident, the victim was on board a barge.FatalDrowningFailure in monitoring of employee
14-05-2012Died falling from height
Location: Kilang - Johor
The victim, a Malaysian citizen, died after falling from a height of 3 metres. A steel pipe which was lifted by a mobile crane struck the victim causing the victim to fall. The victim died at the hospital after 2 days of being unconscious.FatalHit to the head by object after falling down1) No safe work procedure
2) Employer failed to prepare a safe working place
3) Employee were not given appropiate personal protective equipments
26-04-2012Died struck by falling object
Location: Kilang - Kuala Lumpur
The victim, a foreign citizen, died after jack rods fell onto the victim while carrying out works of arranging the jack rods.FatalSuffocationThe accident happened after the fencing could not withstand the load of thousands of arranged jack rods.
22-04-2012Died falling from height
Location: Kedai - Perlis
The victim died after falling from a ladder while carrying out works of bringing down an advertising sign of a shop.FatalBump on head after falling down
22-04-2012Death by suffocation
Location: Tapak bina - Johor
During the incident, the victim was carrying out piling works. Suddenly, the piling machine collapsed and the victim who was in the piling machine cabin could not escape as the cabin sinked into soft earth.FatalSuffocationNo safe work procedures for piling works
22-04-2012Death after being stung by wasps
Location: Ladang - Johor
The victim died after being stung by wasps while patroling the plantation. The victim died at the scene.FatalWasp sting
03-04-2012Died falling from height
Location: Tapak bina - Johor
The victim, a foreign citizen, fell from a height of 16 metres while carrying out works of dismantling aluminium formworks. The victim suffered internal bleedings and died on the way to the hospital.FatalFall from height
19-03-2012Died falling from height
Location: Tapak bina - Perlis
The victim, a foreign worker, fell from a mobile scaffold as he was doing wiring works. The victim died in the hospital.FatalFall from height
12-03-2012Died struck by falling object
Location: Tapak bina - Kuala Lumpur
The victim, a foreign citizen, died after being struck by falling aluminium sheets. The victim suffered serious injuries to the head and was confirmed dead by the hospital after 2 days of treatment.FatalStruck by fallling objectNo practical control measures for works at height
29-02-2012Died after being buried
Location: Tapak bina - Kedah
The victim during the incident climbed down into a newly dug hole to carry out works of installing sewage pipelines when suddenly the land and rocks buried the victim up to the chest. The victim was brought to the hospital and confirmed to have died due to internal injuries.FatalBuriedNo safe work procedures
17-02-2012Died due to drowning
Location: Sg. Tiram - Johor
During the incident, the victim together with another colleague was repairing a sand processing machine on a platform located in the middle of the river. The victim usually crosses the river through a pipeline from the platform to the river banks. While crossing the river, the victim fell into the river and could not be saved.FatalDrowningNo practice of safe work procedures
14-02-2012Died after falling from height
Location: Tapak bina - Kedah
The victim, a foreign national, was killed after falling from a lift entrance opening. At the time, the victim was working on the second floor. The victim's body was found in the lift pit.FatalFall from heightThe lift entrance opening was not covered properly
11-02-2012Died after falling from height
Location: Kawasan kediaman - Johor
The victim, a Malaysian citizen, died after falling from a height of approximately 3.5 metres. A ladder which the victim was climbing slid down and fell to the floor, bringing the victim down with it. The victim died 3 days later in the hospital due to internal bleeding in the brain.FatalFall from heightWeak system of supervising and monitoring workers
03-02-2012Killed after hit by lorry
Location: Tapak Bina - Pahang
The victim died after being hit by a lorry that was reversing suddenly. At that time, the victim was situated direcly behind the lorry.FatalStruck by objectNo safe work procedures
15-01-2012Killed after struck by falling iron rods
Location: Tapak Bina - Kuala Lumpur
The incident happened at around 2.30 pm when the victim was walking towards his work location. Without realizing it, suddenly an iron rod fell down striking the victim. He suffered serious injuries to the head and died at the scene.FatalStruck by objectWorking conditions that are not sufficiently safe
06-01-2012Death by Drowning
Location: Terminal jeti - Johor
At approximately 11 am, an engineer died while diving as he was doing installation works of a catodic protection on a jetty structure. The victim was given CPR but failed to be rescued.FatalDrowningNo safe work procedures
29-12-2011Died after getting caught between objects
Location: Kilang - Johor
The incident happened at approximately 4.45 pm when the victim died after getting caught between the loading bay and the rear part of a trailer.FatalCaught between objectsNo safe work procedures for operating trailer at the loading and unloading bay area.
28-12-2011Killed in an electrocution accident
Location: Kilang - Sarawak
The victim, a foreign national, died of electrocution while doing inspection works of a water pump near a factory. The victim was given emergency medical assistance but died before arriving at the hospital.FatalElectrocutionNo safe work procedures for electrical works
21-12-2011Died due to falling from heights
Location: Tapak Kuari - Johor
The incident happened at approximately around 1.00 pm, involving the victim who was at the time doing drilling works for installing explosives. A landslide occured causing the victim to fall with the landslide from a height of 100 ft. The victim's death was confirmed on the way to the hospital.FatalFall from heightFailure to conduct risk assessment pertaining to drilling works
07-12-2011Died after falling from tree
Location: Kawasan peranginan - Kedah
The victim who works as a coconut tree climber, coconut picker and leaf cutter died when he fell from a coconut tree at 9 metres high. The victim was unconscious and admitted to an intensive care unit (ICU). He was confirmed to have died the next day.FatalFall from heightNo safe work procedures
02-12-2011Died after being hit by lorry
Location: Tapak Bina - Pulau Pinang
During the incident, the victim was carrying out traffic controlling works at a road repairing site (for repairing pavements). While arranging safety cones by the road, he was hit by a reversing lorry. The victim suffered serious injuries and was confirmed dead at the scene.FatalStruck by objectNo safe work procedures
01-12-2011Killed after being hit by car
Location: Tapak Bina - Pulau Pinang
During the incident, the victim, a construction worker was doing road cutting works for installation of new traffic lights. Suddenly a car, believed to be driven fast, came from behind and hit the victim. The victim was thrown as far as 30 metres and died at the scene.FatalStruck by objectNo safe work procedures
28-11-2011Died by electrocution
Location: Pencawang Pengagih Utama - Johor
At around 4.30 pm, the two victims were carrying out installation works of a copper bar onto a wall for a new grounding system. Both of the victims were electrocuted; one of them died while the other suffered injuries to the lower part of the body.FatalElectrocutionNo safe work procedures
25-11-2011Killed by falling dead tree branch
Location: Kawasan Pembalakan - Kedah
At around 3.30 pm, the victim, a logger died after a dead tree branch fell onto him while he carrying out logging works.FatalSerious injuries to the body after being hit by a falling objectNo safe work procedures
22-11-2011Died struck by falling steel I-Beam
Location: Kilang - Pahang
At approximately 2.35 pm, a foreign citizen was struck by a steel I-beam while he was transferring the steel onto a lorry. The victim who suffered serious injuries to the head died at the scene. He was then brought to Tengku Ampuan Hafzan Hospital for further investigation.FatalSerious injuries to the head due to being hit by objectNo comprehensive safe work procedures for works of lifting and lowering using overhead travelling cranes.
31-10-2011Died after falling into sludge holding tank
Location: Loji Rawatan Kumbahan - Perlis
At approximately 6.45pm, the 4 year old victim died when he fell into a sludge holding tank of a sewage treatment plant. The victim is believed to have sneaked into the plant through the drainage underneath the front gate.FatalFall into the a sludge holding tank.The opening of the sludge holding tank was not closed properly.
21-10-2011Died after vehicle plunges into river
Location: Tapak bina - Sarawak
The victim drove a bulldozer through a 40-feet wide road which has a height of 200 metres and 80-degree slope. He is said to have wanted to overtake an excavator but failed. Hence, the victim reversed the bulldozer but it then plunged straight into a river. He was found dead at the scene.FatalPlunged into a riverNo safe work procedures
14-10-2011Death due to electrocution
Location: Kawasan Perumahan - Kuala Lumpur
The victim, a 28-year old local citizen died due to electrocution while installing Unifi cables from a Distribution Board (DB) situated on a telephone pole to a customer's house. The victim was later taken to Selayang Hospital for further actions.FatalThe victim touched a Tenaga Nasional Berhad (TNB) electric cable.No safe work procedures
04-10-2011Died crushed by tower crane
Location: Tapak Bina - Pulau Pinang
The victim, a civilian, was crushed to death by a tower crane. The victim who was sleeping at the time died at the scene when the crane in a free standing condition suddenly collapsed onto the shop house inhabited by the victimFatalCrushed by a tower craneFailure in the crane's foundation
25-09-2011Died crushed by container
Location: Tapak bina - Kuala Lumpur
The victim, a foreign worker, was crushed by a container as it was lowered down by a mobile crane. The victim died at the scene and was taken to HUKM for further investigations.FatalCrushed by objectThe crane operator did not realize that the victim was underneath the container.

No safe work procedures
12-09-2011Dies after falling off roof
Location: Kilang - Johor
During the incident, the victim together with two other workers were installing air conditioning pipes on a roof of a factory building. The victim fell down due to stepping onto a broken roof. He suffered serious injuries and died in the hospital on the same day.FatalFall from heightNo safe work procedure

Employers failed to provide training and supervision for works at heights
26-08-2011Died crushed by iron pipes
Location: Tapak bina - Kuala Lumpur
The incident happened at around 10.15 am at a project site in Jalan Stonor, Kuala Lumpur. It happened on the 50th floor when the victim, a foreign national, was descending iron pipes using a winch. Suddenly, the wire rope of the winch fell off its drum hence the iron pipes crushed the victim who was nearby. The victim suffered serious injuries to the hands as well as a spinal fracture. He was sent to Kuala Lumpur Hospital for treatment, but his death was confirmed by 6.00pm.FatalCrushed by objectThe wire rope fell off the drum causing the iron pipes to fall onto the victim.

Proper maintenance has not been carried out onto the winch.

No safe work procedures
08-08-2011Death due to electrocution
Location: Kilang - Pontian, Johor
The victim is a 25-year old local citizen who works as a welder with 2 years of experience. On the day of the incident, the victim was instructed by his supervisor to carry out cleaning works in the Plo work area. According to witnesses, the victim was found lying on his left side with both of his feet on the "welding bad". He was unconscious and his head was bleeding. There was a portable socket and a 3-pin plug underneath his body. The victim was rushed to Pontian Hospital and but his death was confirmed before he could get any treatment.FatalElectrocutionThe victim's death is due to electrocution from the portable socket that was found underneath his body.

No proper maintenance done to the electric wires.

No safe work procedure.
06-08-2011Died crushed by water tank
Location: Ladang - Johor
The victim, a foreign worker, was crushed to death by a water tank sliding from a tractor. The victim was on his way home after he finished poisoning weeds in a oil palm estate.FatalCrushed by objectThe water tank slipped through the holder of the tractor crushing the victim.

No inspections and maintenances were done on the vehicle before works were carried out.
31-07-2011Pinched by body of truck
Location: Bengkel - Chainage 900, Projek 3F, Kg. Kubang Rusa, Sg Yu, Kuala Lipis, Pahang
During the incident, the victim, assisted by his colleague, was repairing a truck that had damaged its jack system. The jack was fully raised and the truck body was held by a metal barrier that was found on the truck body. As the repair works were being carried out, the victim was sitting on the long shaft but suddenly the truck body fell rapidly onto the victim. The victim, caught between the jack and the truck body died on the spot. The victim died due to serious bleeding after receiving a strong blow on the head.FatalPinchedDied as a result of a strong blow to the head.

No safe work procedures.

The victim did not have the qualification or specific skills relating to machinery repairs.
28-07-2011Died by being crushed by falling object
Location: Tapak projek - Setia Sky Residences-PH2, Lot 28 & 29, Jalan Raja Muda Abdul Aziz, Seksyen 42, Kuala Lumpur
The incident occurred approximately at 2:20 pm when a crane operator was lifting a Concrete Pile Head to put onto a trailer. As the victim was arranging the Concrete Pile Head that was lifted onto the trailer using a Crawler Crane and was suspended to the Main Block (Big Block), suddenly the Single Line Block (Small Block) fell down onto the victim's head. The victim's helmet broke and he died at the scene.FatalCrushed by falling objectThe Single Line Block (Small Block) fell onto the victim's head.

No safe work procedures
04-07-2011Died from falling off an escalator
Location: Ibu Pejabat Jabatan Imigresen Malaysia, No. 15, Tingkat 1-7, (Podium), Persiaran Perdana, Presint 2, 62550 Putrajaya
The incident occurred at about 5.00 pm when the victim, 3, along with his youngest brother were playing near a barrier at level 2 alongside an escalator that goes down to level 1. At the same time, the victim's parents were at Level 2 near the scene of the incident. The victim is believed to have stood on the skirt pane on the outside part, and at the same time his hand was placed on the handrail that was moving downwards. As a result the victim lost his balanced and fell to the ground floor through the spacing (hole) located between the barrier and the "return glass" of the escalator at a height of 12 meters. The victim suffered severe injuries to his head and was sent to Putrajaya Hospital on the day of the incident for further treatment before being sent to the Kuala Lumpur Hospital (HKL), due to the increasingly critical situation. The death of the victim was confirmed at the Kuala Lumpur Hospital on 6th July 2011 at around 1.30 pm.FatalFall from heightThe victim who was at the skirt pane lost his balance and fell from level 2 to the ground floor.

No monitoring.
02-06-2011Died of falling from height
Location: Tapak bina - Taman Putra, Jalan Raja Muda, 01000 Kangar, Perlis
On 02/06/2011 at about 11.00 am, the victim with one of his friends was cutting tree branches using a chainsaw while being carried in a man basket lifted by a crane. While working at a height of 21 metres, the victim suddenly fell down along with the man basket to the ground. The victim who suffered serious injuries to the head and body was rushed to the hospital. He died shortly after being admitted to Intensive Care Unit, Sultanah Bahiyah Alor Setar, Kedah at approximately 10.30 am 03/06/2011.FatalFall from heightVictim fell down to the ground along with the man-basket.

Crane is not well maintained and inspected before been used.
31-05-2011Died rolled over by logging machine
Location: Kilang - Bahagian Log Cutting 3
On the day of accident, the victim who worked as a machine logger driver was moving the logs that has been measured and cut into different sizes from 'log cutting' division to 'log peeling (rotary)' division. The victim during that time was working night shift started from 7.00 pm until 7.00 am. Around 7.15 pm, one of the workers noted that the machine logger was spinning 360 anticlockwise with the absence of a driver. The witness waited for the machine logger to stop spinning so that he can aboard the machine logger. Afterwards, the witness found the victim lying on his side on the ground. Victim is believed died rolled over by the front tyres of the machine logger. Victim was sent to Hospital Miri afterwards.FatalRolled overDriver fell down to the ground and was rolled over.

No safe work procedures regarding to machine logger driving.
23-05-2011Death due to being crushed by 'luffing boom'
Location: Tapak pembinaan - Mukim Batu, Kuala Lumpur
The two victims, one a permenant resident and another a foreign national, died due to being crushed by a luffing boom (of a tower crane) that fell down unexpectedly. During the incident both victims were situated under the crane. Both of them died at the scene due to severe head injury.FatalCrushed by objectThe luffing boom suddenly fell on top of the two victims that were situated directly under the crane.

No safe work procedures.
17-04-2011Death due to landslide
Location: Perladangan- Tanah Merah, Kelantan
The victim, 75, a Malaysian citizen, died when he was buried alive by a landslide. During the incident the victim was doing repairs due to a landslide in a plantation alone. Suddenly the victim was crushed by another landslide. The victim died at the scene.FatalBuried aliveThe victim was trying to do repairs caused by a landslide when suddenly he himself was buried by a landslide.

No safe work procedures.
17-04-2011Died while in confined space
Location: Manhole - Tanjung Tokong, Pulau Pinang
The two victims both being Malaysian citizens, died when they entered a confined space. During the incident they were finishing up their work of cleaning sewerage pipes. Upon entering the confined space, it caused them to suffocate and become unconscious. Both victims died at the scene and were sent to hospital for autopsy.FatalSuffocationThe victims were believed to have suffocated while being in the confined space.

No safe work procedure for works in condined space.
14-04-2011Died crushed by timber
Location: Kawasan pembalakan - Sungai Betis, Gua Musang, Kelantan
The victim, 52, a Malaysian citizen, died when he was crushed by a tree log that rolled over his body. During the incident the victim was carrying out tree cutting works in the logging area. While cutting the trees, the timber rolled over and crushed the victim. He was rushed to the hospital but died upon arriving to hospital.FatalCrushed by objectA tree log that he cut rolled over and crushed the victim.

No safe work procedures
09-04-2011Died falling from height
Location: Tapak pembinaan - Seberang Perai Utara, Pulau Pinang
The victim, 35, a foreign national, died when he fell from a rooftop at a height of 8 metres. During the incident the victim was carrying out 'T-Beam' concrete works for one of the houses still in construction. While he was doing the works he fell to the ground and died at the scene.FatalFall from heightThe victim who was doing concrete works suddenly fell to the ground.

No safe work procedures while carrying out 'T-Beam' concrete works.
05-04-2011Died falling from height
Location: Tapak pembinaan - Kuala Lumpur
The victim, 31, a foreign national, died when he fell from a segment at a height of 10.7 metres. During the incident, the victim was carrying out works to clean up wastes of building materials in an elevated road segment. While he was cleaning up, he fell into an uncovered manhole. He suffered injuries to the head and hand and eventually died at the scene.FatalFall from heightThe victim fell into an uncovered manhole while doing works of cleaning up construction wastes.

No safe work procedures for doing cleaning up works.
29-03-2011Died crushed by tractor
Location: Ladang - Batu Pahat, Johor
The victim, 30, a foreign national, died when he was crushed by a tractor. During the incident the victim was carrying out hole closing works on the road surface. He was driving a tractor carrying earth to close the holes when suddenly the tractor lost its balance and fell over onto the victim.FatalCrushed by objectThe tractor driven by the victim fell over and crushed the victim.

No safe work procedures.
26-03-2011Death by being rolled over by road roller
Location: Ladang Getah Persendirian, Gemas, Negeri Sembilan.
The victim, 18, a Malaysian citizen, died when he was rolled over by a road roller. During the incident the victim was carrying out road levelling works in the plantation using the roller. He stopped the roller and went in front of it to see something when suddenly the roller rolled over him. The victim died at the scene.FatalRolled over by objectThe road roller was on a slope when it stopped, hence it rolled over the victim.

No safe work procedures.
25-03-2011Died being wedged between cages
Location: Kilang - Mukim Bera, Pahang
The victim, 22, an foreign national, died when he was wedged between cages. During the incident the victim was carrying out works of pulling out cages of oil palm fruits from sterilizers. While the victim was pulling out the cages, he ask some shoveling help. As the shoveler was pushing the cages, he found that the victim was caught between the cages and rushed to send the victim to a nearby hospital. The victim died on the way to the hospital.FatalWedged between objectsThe victim was caught between the cages when the shoveler pushed the cages.

No safe work procedures.
16-03-2011Death due to exploding barrel drums
Location: Kilang - Johor Bahru, Johor
A local worker, age 30, died when barrel drums undergoing welding suddenly exploded. During the incident the victim was carrying out renovation works to the drums in order to use them for diesel oil storage. As the victim was welding the cover of the drum, the drum exploded causing the cover to fling towards to chest and face of the victim. He was rushed to the nearest hospital but died after several days of receiving treatment.FatalStruck by objectThe barrel drum undergoing welding by the victim exploded, tossing its cover which hit the victim's chest and face.

No safe work procedures.
09-03-2011Died falling off a ladder
Location: Kemudahan lampu jalan - Kedah
A local worker, age 31, died after he slipped and fell off a ladder. During the incident the victim was carrying out works to change the connections of street lights. As the victim was descending the ladder after completing his work, he suddenly slipped and fell to the ground. The height of his fall was 3.5 metres. The victim was unconscious and rushed to a nearby hospital. He died on 17.03.2011.FatalFall from heightThe victim fell to the ground as he was descending a ladder.

No safe work procedures.
01-03-2011Died falling off trailer
Location: Perladangan - Johor
A foreign worker, age 26, died when he fell off a trailer. During the incident the victim together with a tractor driver entered a farm to collect empty barrels used to store mixtures of herbicides after works of spraying have finished. While the tractor which they rode was descending a hill, the victim fell of the trailer and was hit by the trailer's rear tyre. He died at the scene due to severe injuries at the back of the head.FatalStruck by objectThe victim fell off while riding a trailer and the rear tyre hit him.

No safe work procedures.
24-02-2011Died falling from height
Location: Tapak pembinaan - Johor
A foreign worker, age 30 years old, died when he fell from height. During the incident the victim was on the 8th floor and was bringing down a concrete barrel to a place to pour concrete. Strong winds hit the area causing the barrel to sway and hit the wooden support on the 9th floor. The wooden support broke and fell off. The victim tried to avoid the support causing him to lose his balance and fall to the ground.FatalFall from heightThe incident happened during strong winds as the victim was trying to avoid a falling wooden support.

No safe work procedures.
14-02-2011Died crushed by timber
Location: Pembalakan - Kelantan
A local worker, 26 years old, died due to being crushed by a tree log. During the incident the victim, an excavator driver was doing work of placing tree logs onto a truck. Suddenly a strong gust of wind hit the area. A rotted tree log fell and crushed the victim. The victim died on the way to the nearest hospital.FatalCrushed by objectA strong gust of wind caused a rotted tree log to fall crushing the victim.

No safe work procedures.
13-02-2011Died falling into river
Location: Perlombongan Pasir - Kelantan
A local worker, aged 20, died when he drowned in a river. During the incident the victim, a general worker, was doing repairs on a damaged pipeline of a sand sucker. After completing the repairs, the victim traversed the pipeline to go the river bank to buy some food at a nearby shop. Suddenly he slipped and fell into the river. The river current was very fast, causing the victim to be swept away and drowned.FatalDrowningThe victim slipped and fell while traversing the sand sucker pipeline.

No safe work procedures.
12-02-2011Died falling off portable stairs
Location: Tapak pembinaan - Pulau Pinang
A foreign worker, 32, died when he fell from a height of 5 metres. During the incident, the victim was carrying out spraying works of a material called 'debond release agent' using portable stairs. The material is used to facilitate separation when 'joining processes' are done between segments. The stairs failed to move, so the victim tried to climb onto one of the segments. Upon boarding a segment, he fell down. He died at the scene due to severe head injury.FatalFall from heightThe victim fell down trying to climb onto a segment.

No safe work procedures.
27-01-2011Died being rolled over by tractor
Location: Kawasan Ladang Kelapa sawit, Sarawak
A local worker, aged 47, died by being rolled over by a tractor. During the incident, he was sitting on the mudguard of the tractor. The tractor was on its way to collect oil palm fruits when the front part of the tractor suffered damage. The screw that supports the front weight bar of the tractor broke. The tractor driver hurriedly stopped his tractor causing the victim to fall. The victim was then rolled over by the tractor's tyres.FatalRolled over by objectThe screw that held the front weight bar of the tractor broke. The victim fell. He was rolled over by the tractor's tyres.

No safe work procedures.
12-01-2011Died falling off factory roof
Location: Kilang - Pulau Pinang
A local worker, aged 47, died when he fell off the roof of a factory which was 13.7 metres high. The victim was doing roof repairs at the time. During the incident, the victim accidently stepped on the thermoplastic/PVC part of the roof. The roof broke instantly causing the victim to fall down to the ground. He died at the scene due to severe head injury.FatalFall from heightThe victim accidently stepped on the thermoplastic/PVC part of the roof (which can easily break) causing him to fall down and die.

No safe work procedures.
03-01-2011Death caused by sudden floor collapse
Location: Tapak pembinaan - Kuala Lumpur
A foreign worker, aged 30 years old, died when a floor structure suddenly collapsed. During the incident, the victim was carrying out cement leveling work where the cement was pumped onto the formwork structure. As the cement was being poured, suddenly the structure collapsed. The victim fell with it and was buried by the concrete. The victim died on the spot.FatalFell and buried aliveA floor structure suddenly collapsed. The victim was buried by concrete.

No safe work procedures.
02-01-2011Death caused by falling into machine
Location: Sektor perkilangan - Johor
A foreign worker, aged 34 years old, died when he fell into a wood shredder machine. During the incident, he was given the task of shredding boards using the machine. He fell into the machine while using it. His whole body disintegrated, killing him instantly.FatalFall into machineThe accident happened because the victim was operating the machine alone.

No safe work procedures.
29-04-2010Killed by a tractor commutting to workplace
Location: Serdang, Kedah
The victim, 28, was killed after being involved in an accident on the way to workplace.Fatal
24-04-2010Hit by bulldozer
Location: Kawasan Perindustrian Rembia Fasa 3, Melaka
The victim, 21, was killed after a bulldozer toppled during clearing of the work site.Fatal
19-04-2010Fall from height
Location: Mukim Batu, Kuala Lumpur
The victim, a foreign worker, was killed after falling from height. During the incident, the victim was putting silicon in between the windows mirrors. Unfortunately, he stepped on an area with no mirror installed, and fell down onto the skylift.Fatal
09-04-2010Fell from scaffold
Location: Batu 7 1/2, Lebuhraya Besraya, Kuala Lumpur
The victim, 23, was killed after falling down from scaffold.Fatal
06-04-2010Sudden death after fainting
Location: Senawang Industrial Park, Seremban, Negeri Sembilan
The victim, 40 years,was found death after fainting.Fatal
01-04-2010Fall from height
Location: Jalan Galloway, Kuala Lumpur
The victim, 28 years, a foreign national, was killed after falling from 24th floor to 6th floor. During the accident, the victim was doing cleaning/clearing works at the 24th floor.Fatal
29-03-2010Scaffold collapsed
Location: Mukim Kuala Nerus, Terengganu
The victim, 37 years, a foreign national, was killed after a scaffold collapsed at a construction site.Fatal
21-03-2010Found death in confined space
Location: Beaufort, Sabah
Six victims were killed in a confined space (a treated water pumping tank). They were killed due to toxic gases.Fatal
08-03-2010Hit by a bulldozer
Location: Kuala Lipis, Pahang
The victim, 62 years, was killed after being hit by a bulldozer which was sliding from a slope.Fatal
04-03-2010Hit by a tractor
Location: Kuala Lipis, Pahang
The victim, 43 years, was killed after falling down from a tractor. During the incident, the victim was on the way back after finished collecting oil palm fruits.Fatal
03-03-2010Falling down inside the bin
Location: Kuantan, Pahang
The victim, 25 tahun, from Nepal, died after falling into a bin through its opening. During the incident, the victim was doing scraping works of the bin. Fatal
22-02-2010Hit by excavator
Location: Kuala Rompin, Pahang
The victim, 27 years, from Indonesia, was killed after being hit by an excavator during cleaning activity.Fatal
20-02-2010Hit by bulldozer
Location: Alor Gajah, Melaka
The victim, 14 years, was killed after being hit by a bulldozer. During incident, the victim was playing near the machine.Fatal
17-02-2010Found dead in a toilet
Location: Sungai Udang, Melaka
The victim, 40 years, was found dead in a toilet by other worker.Fatal
16-02-2010Killed in confined space
Location: Kuala Lumpur
Two foreign workers were found dead in a confined space at the sewage plant. During the incident, they were doing cleaning works at the manhole.Fatal
09-02-2010Struck by a tree
Location: Rompin, Pahang
The victim, 39 years, a foreign national, was killed after being struck by a tree (logging).Fatal
01-02-2010Struck by a tree
Location: Tanah Merah, Kelantan
The victim, 55 years, was killed after being struck by a tree (logging).Fatal
01-02-2010Fall from height
Location: Seberang Prai, Pulau Pinang
The victim, 35 years, a foreign national, was killed after falling from a height of 7 metres. During the incident, the victim was installing water cooling cables.Fatal
31-01-2010Drowned at river re-construction site
Location: Pekan, Pahang
The victim, 7 years, was found drowned at a river re-construction site.Fatal
28-01-2010Pinched between objects
Location: Besut, Terengganu
The victim, 45 years, was killed after being pinched between a mobile crane counterweight and the back of a trailer body.Fatal
26-01-2010Fall from height
Location: Bentong, Pahang
The victim, 39 years, was killed after falling from the 3rd floor of a school building. During the incident, the victim was doing painting works and renovating the school building.Fatal
25-01-2010Killed during repair work
Location: Plantation, Setiu, Terengganu
The victim,30 years, a foreign national, was killed after serious burning while doing welding (repair) works on a reactor.Fatal
21-01-2010Buried with waste disposal
Location: Beris Lalang, Bachok, Kelantan
The victim, 44 years, was buried with rubbish in the local district council waste disposal. During the incident the victim was collecting cans and plastic bottles for selling.Fatal
21-01-2010Killed by sanding calibrator machine
Location: Simpang Rengam Industri Estate, Johor
The victim, 35 years, a foreign national, was killed after being struck by a sanding calibrator door, which was not properly closed.Fatal
15-01-2010Struck by an object
Location: Ulu Nenggiri,Daerah Bertam, Gua Musang, Kelantan
The victim, 26 years, was killed after being struck by a tree (logging).Fatal
10-01-2010Struck by an object
Location: Kuala Betis, Gua Musang, Kelantan
The victim, 32 years, a foreign worker, was killed after being struck by a tree (logging).Fatal
05-01-2010Struck by Cooling Tower Fan
Location: Bukit Sagu 4, Kuantan, Pahang
The victim, 34 years old, a foreign worker, was killed after being struck by cooling tower fan while doing the maintenance.Fatal

Kaunter Perkhidmatan

Untuk sebarang urusan rasmi di Ibupejabat JKKP Putrajaya sila berurusan di:

Aras 4 (Kaunter Utama), Blok D3, Kompleks D, Pusat Pentadbiran Kerajaan Persekutuan, 62530 Putrajaya
(T): 03 - 8886 5343
(F): 03 - 8889 2443
Call Centre: 03-8871 1228
(E): Alamat e-mel ini dilindungi daripada spambots. Anda perlukan JavaScript diaktifkan untuk memaparkannya.
Alamat e-mel ini dilindungi daripada spambots. Anda perlukan JavaScript diaktifkan untuk memaparkannya.
( Kaunter Aras 3 )
Alamat e-mel ini dilindungi daripada spambots. Anda perlukan JavaScript diaktifkan untuk memaparkannya.
( Kaunter Aras 4 )
(W): www.dosh.gov.my

Bilangan Pelawat

011146804
Hari Ini
Semalam
Minggu Ini
Minggu Lepas
Bulan Ini
Bulan Lepas
Jumlah
5047
16719
103396
10944167
103396
472538
11146804